Billet clutch perch/lever available SOON!!
Group Moderator
Joined: Sep 2004
Posts: 22,023
From: PA
Re: Billet clutch perch/lever available SOON!!
i always wanted someone to make this style lever.
Someone makes them for motocross bikes for the front brake levers. Id rock one for my front brake and for my clutch
Someone makes them for motocross bikes for the front brake levers. Id rock one for my front brake and for my clutch
Registered User
Joined: Nov 2008
Posts: 325
From: sumwhere pa
Re: Billet clutch perch/lever available SOON!!
Retired
Joined: Mar 2003
Posts: 37,967
From: .
Thread Starter
Registered User
Joined: Jun 2006
Posts: 5,896
From: Where the grapes and ganja be growin!
Re: Billet clutch perch/lever available SOON!!
...pretty yummy lookin, huh!?!
Gotcha, bro!
I agree!
........Next week, bro!
Gotcha!
Gotcha!
Should be about perfect timing, bro.......I'll be shipping next week, if they perform to my expectations. You've been on the list for a while, bro.......I'm holding units for everyone on the list for atleast a few weeks to enable everyone to scrape up the dough.
Certified
Joined: Jan 2003
Posts: 13,792
From: Lauderdale
Re: Billet clutch perch/lever available SOON!!
Cool Cool thanks bro
Thread Starter
Registered User
Joined: Jun 2006
Posts: 5,896
From: Where the grapes and ganja be growin!
Re: Billet clutch perch/lever available SOON!!
UPDATE:
Sooo......it's painfully obvious that my machinist is a lil off his mark with his completion date. He is, however, on schedule to have these bad boys finished by Friday at noon. I'm riding in the Street Bike Fest in Modesto on Saturday, and I told him I would pull my contract w/ him if he didn't have them done by Friday when I leave. He seems to be on schedule from what I see. Levers will go through their second and last operation on the mill this afternoon/evening, and the perches will be running this evening, also. There ARE going to be a few small changes from what my original design was going to be. We found out that the needle bearings used in the Raptors are the MOST expensive part of the ENTIRE Raptor assembly. We are opting to use a Delrin bushing instead of the needle bearings in order to keep the cost down. Two bushings will be included with EACH lever assembly so a spare can be thrown in your tool kit. The Delrin bushing will be much more tolerable of abuse than the bearing, and also be damn near as good at reducing friction on the shoulder bolt.
Secondly.....the ENTIRE assembly, including the lever, will be a lot beefier than an MSR. The perch and the lever will be about 1/8 of an inch thicker than the Raptor assembly. Being made out of much stronger material than the Raptor, and being beefier......and taking the Delrin bushing into account.......the Righteous Stunt Clutch should be damn near bulletproof!
Sooo......my shipping schedule should still be the same. I'll be posting a review AND PMing everyone either Sunday evening or Monday morning, with paypal info.
Even though I'm NOT accepting payments yet, I still want to get this out there...........PLEASE INCLUDE YOUR STUNTLIFE OR STUNTRIDE USER NAME WITH YOUR PAYPAL PAYMENT IN THE MESSAGE BOX! Otherwise I won't know who to check off the "list".
Here's another teaser...
___________
Sooo......it's painfully obvious that my machinist is a lil off his mark with his completion date. He is, however, on schedule to have these bad boys finished by Friday at noon. I'm riding in the Street Bike Fest in Modesto on Saturday, and I told him I would pull my contract w/ him if he didn't have them done by Friday when I leave. He seems to be on schedule from what I see. Levers will go through their second and last operation on the mill this afternoon/evening, and the perches will be running this evening, also. There ARE going to be a few small changes from what my original design was going to be. We found out that the needle bearings used in the Raptors are the MOST expensive part of the ENTIRE Raptor assembly. We are opting to use a Delrin bushing instead of the needle bearings in order to keep the cost down. Two bushings will be included with EACH lever assembly so a spare can be thrown in your tool kit. The Delrin bushing will be much more tolerable of abuse than the bearing, and also be damn near as good at reducing friction on the shoulder bolt.
Secondly.....the ENTIRE assembly, including the lever, will be a lot beefier than an MSR. The perch and the lever will be about 1/8 of an inch thicker than the Raptor assembly. Being made out of much stronger material than the Raptor, and being beefier......and taking the Delrin bushing into account.......the Righteous Stunt Clutch should be damn near bulletproof!
Sooo......my shipping schedule should still be the same. I'll be posting a review AND PMing everyone either Sunday evening or Monday morning, with paypal info.
Even though I'm NOT accepting payments yet, I still want to get this out there...........PLEASE INCLUDE YOUR STUNTLIFE OR STUNTRIDE USER NAME WITH YOUR PAYPAL PAYMENT IN THE MESSAGE BOX! Otherwise I won't know who to check off the "list".
Here's another teaser...
___________
Thread Starter
Registered User
Joined: Jun 2006
Posts: 5,896
From: Where the grapes and ganja be growin!
hate practitioner
Joined: May 2004
Posts: 5,437
From: murder mitten
Re: Billet clutch perch/lever available SOON!!
mother trucker, besides u ive been waiting the longest to get this thing
cause the msr is going on my streeter and the stunt piece is getting this thing
soooooooooooooo ya
how bout that N on there? huh huh
cause the msr is going on my streeter and the stunt piece is getting this thing
soooooooooooooo ya
how bout that N on there? huh huh
Thread Starter
Registered User
Joined: Jun 2006
Posts: 5,896
From: Where the grapes and ganja be growin!
Re: Billet clutch perch/lever available SOON!!
I can't wait either, bro!You want me to ask the machinist to do something else....NOW??? Sorry, my man......I'm not askin him to do anything other than finish what I asked him to start! Maybe later down the road when you buy another one to replace the MSR on the streeter.....we'll talk about it then.
Thread Starter
Registered User
Joined: Jun 2006
Posts: 5,896
From: Where the grapes and ganja be growin!
