I will have to make sure you can swap sides on these since the risers determine the height as well as the degree; They have notches in them for support so I'll make sure those line up when flipped too.

I've only run the 0 Degree ones on mine so it makes no difference.

 

i think if i were to get the swat clips i think if you take the height peices off and switch them,they should be fliped,without having to really flip the clipon bracket....
heres my set up right now,,i would like it just a touch higher...

 

i see..... if all else fails you could go with the F.T.I. setup

 

yea they look dope but they wont work with the hohey...

 

Havok, why don't you just ditch the hohey triple and go with a higher rise and a stock upper triple?

 

because the trip was $$$

 

sell it

 

true but i think id rather buy clips for 140 and take a $30-40 loss and have to re sell them if they dont work..
then sell the trip and get the clips then the clips dont work,know what i mean...

 

I see you problem with puting these on your tripple. If they werent a split clamp you'd be set.

I never understood why clipon companies brag about having a split clamp and how easy it is to install them, when if you think about it, you have to take the tripple of anyways to get the existing clamps off if they mount below the tripple.

I guess you could be ghetto and just leave the old ones on and out of the way

How thick is the tripple around the fork on the HoHey? Say if you were gonna mount them underneath the tripple.
These may work like that and wouldn't hit the tripple at all if you get the higher rise ones. May look kinda funny tho with a step down on the top of your tripple with nothing there.

I know of some bars that will work with your setup that are gonna be out soon

:threadjack

 

yea the clips would be way low under the trip and would look like *** and would hit the frame...

hopefully you get them done before summer....

 

Agreed.
I think these bars are a nice setup if they work for your application.

If you get time tho let me know how thick it is just for the extra info.

If all you need is about a 1 1/4" rise above what you have and some adjustment to boot let me know I may have an answer sooner than expected.


Sorry to thread jack again

 

well the thickness is 3/16th of a inch
and width is one inch..

 

yeaaa budddy

to my understanding thats what im planning on doin. ordered the 50mm 5 degree 2.5" rise goin under the tripple of my f4i w/1krr clip ons

just gunna swap the sides to have the upward rise im used to wit 636 stockers!

im so excited i might be able to pull through to podium now

 

let me know if that works,I wanna do the same thing cause I hate 0 degree clip-ons.

ps. the trick for podium is to stick your leg through sideways, just above the clutch(if your using right foot).Straight through,above the triple tree is waaaaay harder.

 

oh you mean your running 1000rr forks and triples? no hohey??

 

im bout 5'8" and drink beer so as u can see its a bitch wit clips underneath the trip and my belly being in the way doesnt help either!







check it out^^^ im runnin 929/54 triples and wheel wit 1krr forks

 

so when do i get them AJ??? im gettin ready to sell this bitch but couldnt hold out on tryin these

 

So whats everything think about running these with the risers?

My friend is in the market for clip-ons, hes like 6'6" or taller.. I was thiking of having him order the 1.5" so he can have clip-ons, that stand sorta tall like mx bars

oh ya for a f4i!

 

based off your pictures, there doesn't look like there is much room for a handbrake. please tell me i;m crazy I really want a pair

 

My setup from bill at fulltrottle