didnt get much help in the repair section, so i will try here.
07-02-2008 | 06:39 PM
#1
Thread Starter
Registered User
Joined: Dec 2006
Posts: 1,147
From: terre haute indiana usa
didnt get much help in the repair section, so i will try here.
my boy took a hard fall on his 01 f4i the other night. bent his rear rim , and clipp on. he wanted some db bars so i went ahead and threw some on for him. startred the bike and it ran fine. the next day he came by and wanted to pound the lip down on his rim so it would hold air. he laid the bike on the right side and went to work. got the wheel fixed, now the bike wont start. here is what a have done so far... new plugs, ignition is fine, kill switch is fine, tip over sensor fine, stator is fine, have got power at the crank sensor, power to the ecu, but nothing to the plugs. all grounds are fine, and all relays, and ecu have been replaced. rectifier replaced. i even went ahead and put a new wire harness on it and still have no spark at the plugs! what am i missing? help me out here!!!!
07-03-2008 | 12:38 AM
#11
Registered User
Joined: Sep 2005
Posts: 1,665
From: georgetown, tx
Re: didnt get much help in the repair section, so i will try here.
pulse generator look at right side case cover #8 on the diagram
http://www.bikebandit.com/houseofmot...4-2002/o/m2051
prolly jarred it loose after the crash then hitting the rim with a hammer while attatched to the bike
http://www.bikebandit.com/houseofmot...4-2002/o/m2051
prolly jarred it loose after the crash then hitting the rim with a hammer while attatched to the bike
Last edited by spiller03; 07-03-2008 at 12:49 AM.
07-03-2008 | 08:22 AM
#12
Thread Starter
Registered User
Joined: Dec 2006
Posts: 1,147
From: terre haute indiana usa
Re: didnt get much help in the repair section, so i will try here.
pulse generator look at right side case cover #8 on the diagram
http://www.bikebandit.com/houseofmot...4-2002/o/m2051
prolly jarred it loose after the crash then hitting the rim with a hammer while attatched to the bike
http://www.bikebandit.com/houseofmot...4-2002/o/m2051
prolly jarred it loose after the crash then hitting the rim with a hammer while attatched to the bike
this is what i was thinking last night! i will chk it today. thanks bro!
07-03-2008 | 08:26 AM
#13
Thread Starter
Registered User
Joined: Dec 2006
Posts: 1,147
From: terre haute indiana usa
07-03-2008 | 09:14 AM
#14
Registered User
Joined: Jul 2006
Posts: 10,842
From: Lewiston ME, USA
Re: didnt get much help in the repair section, so i will try here.
my boy took a hard fall on his 01 f4i the other night. bent his rear rim , and clipp on. he wanted some db bars so i went ahead and threw some on for him. startred the bike and it ran fine. the next day he came by and wanted to pound the lip down on his rim so it would hold air. he laid the bike on the right side and went to work. got the wheel fixed, now the bike wont start. here is what a have done so far... new plugs, ignition is fine, kill switch is fine, tip over sensor fine, stator is fine, have got power at the crank sensor, power to the ecu, but nothing to the plugs. all grounds are fine, and all relays, and ecu have been replaced. rectifier replaced. i even went ahead and put a new wire harness on it and still have no spark at the plugs! what am i missing? help me out here!!!!
07-03-2008 | 09:50 AM
#15
Thread Starter
Registered User
Joined: Dec 2006
Posts: 1,147
From: terre haute indiana usa
Thread
Thread Starter
Forum
Replies
Last Post
