sup all i jsut got my gixxer 750 a few weeks ago and i can pult the front up with no problems in first by just rolling on the throttle...
but i hate doing 1st gear wheelies! i flipped a bike a few weeks back by doing that...
so i have a question for all u 00' - 03' gixxer 750 riders
in second how fast/rpms to pull it up without the clutch? and also to do standups?
cuz everyone is telling me standups are much easier then sit downs¿?
also in 2nd do i have to clutch it up at all?
im only 120 lbs so i know it shouldnt take much effort but i seem to just get the wheel about 1' off the ground when i try to clutch it and sitting all the way back o nthe seat. and last night i tried to do a standup in 2nd and was at around 8-9k rpm and the front only came up about 2' then dropped again...
so if anyone can give me some insight on how to do these nice and smooth it would help me from flipping over again hehe
thanx

 

Well I'm in the same boat. I'm only 125lbs. I have the same kinda trouble with my standups, and i know its not the bike, my skillz are just weak. I almost always use the clutch in second. I roll on the gas goin' about 50 wack it wide open then pull the clutch just enough for the rpms to jump way up and then dump it back out. The front tire should come flyin up nice and smooth. Also to get the standups up make sure your bouncin on the pegs and not just the front shocks. Shut the gas fully and wack it wide open, push your feet down and forward on the pegs and lean back. This is all the stuff that works for me but I could be way off, like i said my skillz are weak. just my. One last thing, when learning remeber to cover the back break.

 

i try to cover the rear break...
dosnt allways work
also i dont like to clutch it up but ive tried and it comes up alittle...
still need to figure out when and where to pull it up in the rpm range to do standups in 2nd

 

Ok I have no skills either but this is what I do. I would say bring your bike anywhere from 5000 - 7000 rpm's then you have to do this series of things 1. Bounce the bike 2. Get off the gas and right back on it 3. Pull it up with your arms. If you’re still having trouble go down 1 tooth on the front sprocket this will help a lot.

 

i know i shouldnt have to go down any theeth...
theres some chubby kid around here o na bone stock 02 gixxer 600 and he can bounce it up in 3rd.
granted im not anywhere near 200 lbs...
ill give the 7-9k rpm a try today
i was playing in 1st earlier today and had the shield come to my chest, but still not co0 in 1st....

 

Do a search for standups on this site. There's some good stuff.

 

To bring it up in second there's no problem . You have to bring the rpm up to about 10 000 and then let go of the gas and snap it back again . The front will come up real easy . Get the sitting wheelies down first then try out the stand-ups . For the stand-ups you have to bounce the pegs and the front shocks a little and it will come up real easy . You can even do it in 3rd if you want to . Good luck and have fun...but mostly...be careful

 

alright guys, I have a 2000 Gix 750. its hard to do it, but if you want to do nice and easy stand up go to the bike shop. go 1 tooth down in the front. the 2000-2003 Gix 750 has a 16t front, get a 15t. I can do stand ups in second with ease. but practice bouncing the front suspension. do that around 7-8k rpms, bounce and gas it'll come right up in the stand ups. good luck guys, but be careful until ya get the feeling



Chris

 

...well ive been playing around alot lately and im gettign them really nice now
i can clutch it up i n2nd sitting down woth no problems and its even easier with chicks on the back
but as for the standups i can bounce them up i n2nd and 3rd now.
at around 7-8k but ive been using my left arm alot and now its killin me
and i still have to perfect them so im not hitting rev limiter...

 

does going down a tooth on the front make a big difference ? does it make it alot easier for standups, do you loose alot of top end ? sorry for all the questions.

 

its all about timing, on my 00 750 i would be going 50-55 hit the gas, pump and pull and up she came, i had stock gearing, but once it was over 75 in 2nd gear, it was just too high in the rev range for me, so i jus did 3rd instead lol