Tha Alabama Bullshit Thread
Registered User
Joined: Jun 2006
Posts: 3,016
From: B'ham AL
Re: Tha Alabama Bullshit Thread
Beto I got a 05 rear axle if you don't get one with your swingarm, have one spacer but can't remember which side it goes to, I can check. The axle is shorter than 03-04 and the right spacer is diff I think. I'll gladly take your 03-04 in on trade..lol
Registered User
Joined: Jun 2006
Posts: 3,016
From: B'ham AL
Re: Tha Alabama Bullshit Thread
I know the axle is differant, the left spacer is the same, but I can't remember on the right spacer.. I could only find one of the spacers last night but still have a few boxes to go through and I know I had it... I'm pretty sure the right spacers was differant but someone should know for sure on here.
Registered User
Joined: Jun 2006
Posts: 3,016
From: B'ham AL
Re: Tha Alabama Bullshit Thread
Oh and if I remember right the right side swingarm seal has to be swapped.. or is it left..lol
Just look up the swap thread and let me know if you need any other parts I got a few laying around
Just look up the swap thread and let me know if you need any other parts I got a few laying around
...
Joined: Jun 2003
Posts: 9,589
From: Us
Re: Tha Alabama Bullshit Thread
...
Joined: Jun 2003
Posts: 9,589
From: Us
Re: Tha Alabama Bullshit Thread
No pics but it is very simple, all you have to do it take out the rubber seal on the right side of the 05 swingarm and swap it for the one from the 03/04....That will allow you to use the threaded adjuster nut from 03/04 swingarm, so swap the seal use the 03/04 adjsuter nut and piviot shaft....Bolts right up....
YOU MUST ALSO REMEBER! That if your using the 05+ swingarm then you need to make sure the cush drive spacer on the left side must also be 05+....The cush itself is the same but those spacers are difernt widths, so if you use the 03/04 spacer with a 05+ swingarm your chain will be out of alignment...And vise versa
Then comes the shock! If you use the 03/04 stock and linkages then nothing needs to be done, however if you want to use the 03/04 knuckle with the 05 shock you need to swap the bottom(where the bottom shock mount bolt goes) 2 seals and bushing from the 05 knuckle into the 03/04 linkage....Because the 05 shock eyelet on the bottom is a little narrower, so for it to fit those need to be swapped.....The knuckle and its roller bearings are the same but the 2 seals and bushing are differnt widths...If you have the 05 knuckle then it will all bolt right up.....Also do not use the 05 upper mount (the steel part that mounts the shock to the frame, 05 is dark colour and 03/04 is silver, use the 03/04 on the 03/04 frame no matter what shock you use)
Its kinda confusing to explain but if you have any specific questions, ask away....
YOU MUST ALSO REMEBER! That if your using the 05+ swingarm then you need to make sure the cush drive spacer on the left side must also be 05+....The cush itself is the same but those spacers are difernt widths, so if you use the 03/04 spacer with a 05+ swingarm your chain will be out of alignment...And vise versa
Then comes the shock! If you use the 03/04 stock and linkages then nothing needs to be done, however if you want to use the 03/04 knuckle with the 05 shock you need to swap the bottom(where the bottom shock mount bolt goes) 2 seals and bushing from the 05 knuckle into the 03/04 linkage....Because the 05 shock eyelet on the bottom is a little narrower, so for it to fit those need to be swapped.....The knuckle and its roller bearings are the same but the 2 seals and bushing are differnt widths...If you have the 05 knuckle then it will all bolt right up.....Also do not use the 05 upper mount (the steel part that mounts the shock to the frame, 05 is dark colour and 03/04 is silver, use the 03/04 on the 03/04 frame no matter what shock you use)
Its kinda confusing to explain but if you have any specific questions, ask away....
k so sounds like I need to swap out seals on the right side of the swingarms, and I need the 05-06 636 left side spacer on the wheel.
And in one of the threads I read that that 03-04 shock will scratch everytime you clutch up, so does anyone have an 05-06 shock?
I Love To Post!
Joined: Oct 2006
Posts: 9,614
From: Lexington, KY
...
Joined: Jun 2003
Posts: 9,589
From: Us
Re: Tha Alabama Bullshit Thread
you can have the 03 swingarm thats on it! 
STUNTRIDE FRONTLINE
Joined: Jun 2005
Posts: 13,621
From: GEORGIA
Registered User
Joined: Sep 2007
Posts: 460
From: TROY OHIO
Re: Tha Alabama Bullshit Thread
Aww **** Compton Just Called Me And Told Me That Everyone Was Out Doing Debo Wheelies Out At The Lot! Im Glad Yall ******* Name A Wheelie After Me Lol! I Cant Wait To Come Down Guys I Need To Get A Good 4 Day Lot Session In!
STUNTRIDE FRONTLINE
Joined: Jun 2005
Posts: 13,621
From: GEORGIA
Re: Tha Alabama Bullshit Thread
Registered User
Joined: Jun 2006
Posts: 3,016
From: B'ham AL
Re: Tha Alabama Bullshit Thread
I got the shock and linkage off the 05.. rear axle and what looks like a left side 05 wheel spacer. it's the thick one with out the lip on it and Ti so. compton must still have the right side spacer.
I'll swap you parts and help you do it just let me know when you want to.
I'll swap you parts and help you do it just let me know when you want to.
STUNTRIDE FRONTLINE
Joined: Jun 2005
Posts: 13,621
From: GEORGIA
