How to hotwire fan on 600RR, info please! which wire should i ground to the frame? there's a blue and and a green one (if im not mistaken) that go to the fan. if i ground the correct one out it should run, right? dont really fee like cutting both wires to check, i only want to cut the right one.. help is very much appreciated!:cheers |
Re: How to hotwire fan on 600RR, info please! ok so i am a total NOOB at electrics.. i checked the wiring diagram and it seemed the black wire was the ground-wire. i cut that wire and held it to the engine and to a groundingpoint but the fan didnt come on.. anybody know what i am doing wrong? |
Re: How to hotwire fan on 600RR, info please! [quote=da Liks;3786875]ok so i am a total NOOB at electrics.. i checked the wiring diagram and it seemed the black wire was the ground-wire. i cut that wire and held it to the engine and to a groundingpoint but the fan didnt come on.. anybody know what i am doing wrong?[/quote]i have not done one on a 600rr myself but the two wires going to the fan are power wires , you need to bypass the temperature sending unit with a switch |
Re: How to hotwire fan on 600RR, info please! the whizzat? whuwhut? where? |
Re: How to hotwire fan on 600RR, info please! [quote=da Liks;3786896]the whizzat? whuwhut? where?[/quote]:LOLmaybe you should let some one else do it for you |
Re: How to hotwire fan on 600RR, info please! I just put mine on a switch. But i want to wire it so it comes on when i turn the key on. |
Re: How to hotwire fan on 600RR, info please! i don't know if this is right or not but it was a sticky on a cbr forum ...... [QUOTE]DONT use some speaker wire or narrow ass wire, use at least 18g wire. Like this: [URL="http://www.partsamerica.com/ProductDetail.aspx?categorycode=4022B&mfrcode=DOR&mfrpartnumber=85732"]http://www.partsamerica.com/ProductD...rtnumber=85732[/URL] Steps: 1.Remove the 3 bolts on the Left side ( the clutch lever side ) mid fairing and any other push clips holding the fairing & Remove. 2.There will be 3 Relays next to each other with wires coming off. Seperate the MIDDLE relay. 3.There are 4 Wires coming out of it as follows: -Black/White = Ground -Blue/Black = Fan -Blue/Orange = Constant Power (12v) -Blue/Green = Trigger (what triggers the relay, works when 12v is applied) 4.Strip a section on the Blue/Black & Blue/Orange Wires. 5.Soder a seperate wire to each wire: ( Blue/Black & Blue/Orange ). 6.Connect the ends of the wires ( the ones you just added ) to the switch. 7.Tape everything up ( or heatshrink ) 8. Now the switch can activate the fan at any given time, but remember to turn it off. NOTE: For those who just want the fan on all the time instead of using a switch just connect the BLUE/BLACK to IGNITION. Also DO NOT just cut the Blue/Black & Blue/Orange wires because if the bike gets hot and you dont turn the fan on, it will overheat.[/QUOTE] |
Re: How to hotwire fan on 600RR, info please! you heroe! |
Re: How to hotwire fan on 600RR, info please! i had my brother come over and do the soldering. We took the pins out of the relay and soldered the wire into the pins and plugged them back in, made a switch on the sidefairing bracket.. works perfect! thanks rog.. |
Re: How to hotwire fan on 600RR, info please! omr for president |
All times are GMT -4. The time now is 04:27 PM. |
© 2024 MH Sub I, LLC dba Internet Brands