#6 appears to have the bubbliest *** so i'd go for her.

 

+1

bornes truck is next to mine

 

OMR SUBCAGE (S)
OMR SUBCAGES available:
Honda

• CBR F4i - 01, 02, 03 <<< click here, will also fit the single seat style with minor mods
• CBR 954- all years
• CBR 929- all years
• CBR 600RR - 03 , 04 , 05 , 06 , 07 , 08<<< click here

Kawasaki

• zx6r/rr (636) - 03, 04, 05, 06 07 08<<< click here

Suzuki

• GSXR 600/750 -00, 01, 02, 03, 04, 05
• GSXR 1000 -01, 02, 03, 04

Yamaha

• R6 - 03, 04, 05 <<< click here
• R6s (old body style) - 06, 07, 08

$175 Shipped
pay pal accepted

Tech

• The 03-06 CBR 600RR , 03-05 Yamaha R6 ,03 04 gsxr 1000 and the f4i pegs are lowered and moved back and out for better peg position! !
• The 01-03 GSXR 600 and 750 have the pegs moved out two inches because of the big tail section
• THE 07 600RR pegs are located 2-1/2 inches lower and 3 inches wider (Than stock)
• All other omr subframe cage models are in the stock location except they are rotated on their axis so they don't fold up unless you fold them up, this also puts your foot on the grippy part of the peg during a wheelie.
• omr subcages are available for all makes and models but only the ones listed above are available for shipping

click here to contact >> old man roger

the original folding peg subcage!!!!!!!!

>>click here to see why i only sell folding peg subcages<<

 

nice

num 7 is over all hottest

 

 

the first one looks like a young christina applegate

if you are using a tig with out a foot pedal you are waisting your time

the "ingredients'' are not the same and yes you can controll the heat and the flow of material much better

 

i would take 6 from the neck down i dont like her face. but 7 is ****** hottttt

 

LOL, this would totally be me

 

don't lie you like #5

 

#3's head is photo shopped

 

god bless Al Gore for inventing the internet

 

there was a number 5

 

ingredients = heat and metal filler. whats the difference in the rods versus the wire?


-->

 

i think 1 2 3 4 are all photo shop

 

i don't think it is, cuase 4's head looks like it could be also, so it's probably the light

 

i like 6's face but yah, 7's is prettier. i gotta have major *** though, so 6 has my vote.

 

you can have the one on the right, whiteboy, LOL

 

hey man get it where you can fit it. and she has a few rolls so its like havin all at once

 

like regular welding rods there are many options of filler rod and there is also a tungsten tip which also induces gas along with the argon ...

tungsten inert gas
Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding process that uses a nonconsumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually an inert gas such as argon), and a filler metal is normally used, though some welds, known as autogenous welds, do not require it. A constant-current welding power supply produces energy which is conducted across the arc through a column of highly ionized gas and metal vapors known as a plasma.
GTAW is most commonly used to weld thin sections of stainless steel and light metals such as aluminum, magnesium, and copper alloys. The process grants the operator greater control over the weld than competing procedures such as shielded metal arc welding and gas metal arc welding, allowing for stronger, higher quality welds. However, GTAW is comparatively more complex and difficult to master, and furthermore, it is significantly slower than most other welding techniques. A related process, plasma arc welding, uses a slightly different welding torch to create a more focused welding arc and as a result is often automated