OMR SUBCAGE (S)
OMR SUBCAGES available:
Honda

• CBR F4i - 01, 02, 03 <<< click here, will also fit the single seat style with minor mods
• CBR 954- all years
• CBR 929- all years
• CBR 600RR - 03 , 04 , 05 , 06 , 07 , 08<<< click here

Kawasaki

• zx6r/rr (636) - 03, 04, 05, 06 07 08<<< click here

Suzuki

• GSXR 600/750 -00, 01, 02, 03, 04, 05
• GSXR 1000 -01, 02, 03, 04

Yamaha

• R6 - 03, 04, 05 <<< click here
• R6s (old body style) - 06, 07, 08

$175 Shipped
pay pal accepted

Tech

• The 03-06 CBR 600RR , 03-05 Yamaha R6 ,03 04 gsxr 1000 and the f4i pegs are lowered and moved back and out for better peg position! !
• The 01-03 GSXR 600 and 750 have the pegs moved out two inches because of the big tail section
• THE 07 600RR pegs are located 2-1/2 inches lower and 3 inches wider (Than stock)
• All other omr subframe cage models are in the stock location except they are rotated on their axis so they don't fold up unless you fold them up, this also puts your foot on the grippy part of the peg during a wheelie.
• omr subcages are available for all makes and models but only the ones listed above are available for shipping

click here to contact >> old man roger

the original folding peg subcage!!!!!!!!

>>click here to see why i only sell folding peg subcages<<

 

 

nice

 

err didnt turned out good... u guys use photo chop? :p

 

Lmfao!!!!

 

where's my stick?

Best Car & Motorcycle Insurance | Auto/Moto Protection Today | FREE Trade-In Quote

 

here ya go R6

feels like butta too :YEAH





i have another lever on the way for the master and i need to chop down the clutch but i feels good

 

and heres the ignition

 

not bad

 

one thing though, on the master where the switch goes you need to remove that switch (of course) but grind down the mounts the switch goes on and break the tab that pushes in the switch off the lever or the clutch will hit it...

 

mount the brake inboard of the clutch, THEN cut down the clutch lever

 

When I can afford the adaptor and line... I will dig out the f.b. master like yours and try it out.. I tried mounting up the clutch master and was not thrilled about the fit

 

ill try that once i get the new lever...

reason i put it like that is because the lever was already broke off there and it was the only way i could reach it... it feels pretty good like that though.. i went down to the garage earlier and pumped it up and cracked the banjo one more time and a **** load of air came out... feels rock hard now

 

watching some lesbian foot fetish vide on tube8.com

good site

 

it's about that time....

 

i have a line that ill sell ya, it just doesnt have the fittings... its the screw in fittings though, you can buy em through HAI, i think their like $8 a peice

 

with them stock bars being so short clutch on the outside don't work so well....At least for me...I have a msr and it puts my finger in board of the right spot....

on the R6 and ol' F4i I got/had the vortex bars and had the room to mount it the right way

 

cape cod chips are the bomb diggity!

 

No thanks....I'll hold out for the crimped on kind

 

******' bored..

Watching a movie, but it isn't doin' much for me.