is this proper way to do f4i clean air mod??????
08-04-2008, 04:30 PM
#21
Registered User
Join Date: Jul 2008
Location: lakeland fl
Age: 36
Posts: 87
Re: is this proper way to do f4i clean air mod??????
the easiest way to keep oil from gettin into ur intake is to cut the crankcase breather hose and install a pcv valve into the middle of the hose this way it allows it to still vent but restricts oil from getting to the top of the pistons and locking the motor
08-04-2008, 04:33 PM
#22
Squid Extradoinaire
Join Date: Oct 2005
Location: NE INDIANA
Age: 39
Posts: 5,893
Re: is this proper way to do f4i clean air mod??????
ive never had a problem. i usually um turn my bike off if i can once its on the ground.
ive put if off for to long. i guess ill do it with the weekly maintenace this week.
ive put if off for to long. i guess ill do it with the weekly maintenace this week.
10-09-2008, 04:53 PM
#23
Registered User
Join Date: Sep 2003
Location: kingston jamaica
Age: 49
Posts: 355
10-09-2008, 07:01 PM
#24
Registered User
Join Date: Sep 2003
Location: kingston jamaica
Age: 49
Posts: 355
Re: is this proper way to do f4i clean air mod??????
hey im trying to do mine and i dont understand entirely do i get an entirely new t valvle or use the silver t thing that's already there hooked up to the neck of the frame
10-11-2008, 08:35 AM
#29
hunts and stunts
Join Date: Feb 2007
Location: KC
Age: 49
Posts: 3,089
Re: is this proper way to do f4i clean air mod??????
There was a mod where you shove a marble in one of the rubber hoses goin to the airbox on my K6 gix pluggin it up tight.
Not sure if it did the same thing or if I need to do a type of clean air mod to it like I did to my F4i...
Anyone familiar with what I'm talkin about? It's kinda scary thinking that I was raggin **** outta that bike, and bouncin it off the lot left and right, and I never had a failsafe for hydro-lock!
Not sure if it did the same thing or if I need to do a type of clean air mod to it like I did to my F4i...
Anyone familiar with what I'm talkin about? It's kinda scary thinking that I was raggin **** outta that bike, and bouncin it off the lot left and right, and I never had a failsafe for hydro-lock!
10-11-2008, 09:01 AM
#30
Registered User
Join Date: Jul 2007
Location: Ill State Boyz, Bloomington, IL
Age: 42
Posts: 176
Re: is this proper way to do f4i clean air mod??????
the reason they dont come from the factory like that is the job of it is to inject fresh air into the exhaust to lower emissions, it reduces NOx and hydrocarbons.
the reason it gives you more horsepower is it creates more of a vac in the crankcase and seals the engine rings.
the r6's bennift the most.
the reason it gives you more horsepower is it creates more of a vac in the crankcase and seals the engine rings.
the r6's bennift the most.
01-17-2009, 03:07 AM
#31
Registered User
Join Date: Jan 2009
Location: Carlsbad, CA
Age: 41
Posts: 397
Re: is this proper way to do f4i clean air mod??????
So, the hose marked #3 comes out completely, and #4 plugs into where #3 came off the T valve? Then #1 and #2 connect to the T like in the Photo? Then you seal up the airbox how?
01-17-2009, 03:42 AM
#32
Bacons Hot, Need a Spot
Join Date: Jul 2007
Location: Kauai HI, free today FTP
Age: 48
Posts: 1,347
Re: is this proper way to do f4i clean air mod??????
^^1&2 connect to #4, I used a T from the hard ware store, and left the original T pluged in zip tied out of the way(it had wires opposed to vacum lines, an 07 zx6r). As for pluging the air box holes be creative, vacum cap(big) Jam a marble in a short length of hose, a rubber and a zip tie, duct tape what ever.
01-17-2009, 05:01 PM
#33
Registered User
Join Date: Oct 2008
Location: colorado springs,co
Posts: 276
Re: is this proper way to do f4i clean air mod??????
^^1&2 connect to #4, I used a T from the hard ware store, and left the original T pluged in zip tied out of the way(it had wires opposed to vacum lines, an 07 zx6r). As for pluging the air box holes be creative, vacum cap(big) Jam a marble in a short length of hose, a rubber and a zip tie, duct tape what ever.
hey what did you zip tie it too. i did the same thing tied it to the new hose running to the crank case but i think its vibrating on the inside of the frame or something.. might just need to tie it up tighter idk??
and yeah same bike
01-18-2009, 12:41 AM
#40
Registered User
Join Date: Jan 2009
Location: Carlsbad, CA
Age: 41
Posts: 397
Re: is this proper way to do f4i clean air mod??????
so..... no hoses out of these 4 are going to be connected to the airbox? It would be cool to see a before and after pic of the hose routing. Cant tell with this pic.
