No muffler
Call me *Point Blank*
Joined: Apr 2008
Posts: 838
From: Tre4 NC/Mocksville
Registered User
Joined: Jan 2008
Posts: 40
From: SOUTH FL
Re: No muffler I have wanted to do this for a while .... found a post on an R1 forum
http://www.r1-forum.com/forums/showthread.php?t=100536
Gives you a run down on what you need for a to make an ok baffle could be better to buy one from an exhaust manufacturer lil more cash but probably be better off kinda curious how this would look on my 900rr..
http://www.r1-forum.com/forums/showthread.php?t=100536
Gives you a run down on what you need for a to make an ok baffle could be better to buy one from an exhaust manufacturer lil more cash but probably be better off kinda curious how this would look on my 900rr..
rock stock
Joined: Aug 2003
Posts: 5,943
From: dub-bizzle, mass
Re: No muffler
just seems stupid to me. it really serves no purpose at all other than to be way too loud all the time 
if you really need it out of the way for stunting then get rid of it. but i dont think this is the case in this thread
if you really need it out of the way for stunting then get rid of it. but i dont think this is the case in this thread
Last edited by xXxNO LOVExXx; Jun 19, 2008 at 03:01 PM.
Thread Starter
Registered User
Joined: Feb 2008
Posts: 163
From: Mount Dora, Florida, US
Registered User
Joined: Jan 2008
Posts: 422
From: Fort Lauderdale, Stuntshine State
Thread Starter
Registered User
Joined: Feb 2008
Posts: 163
From: Mount Dora, Florida, US
Registered User
Joined: Jan 2008
Posts: 422
From: Fort Lauderdale, Stuntshine State
Re: No muffler
Ya, make sure to composite blade on a chop saw for best results, after u cut it shorter and drill new holes to rivet the end cap back on take some epoxy on a brush to the areas that have been cut and drilled so the fibers dont come apart there. make sure u cut the length u want off from can from the exhaust tip side, thats the side that is free to come lose inside the can. drill the rivets out first and take the end cap off. leave the packing in and take the chop saw and cut. put the end cap back on and mark ur holes to drill, then just rivet it back together. Only cut a couple inches off there's no need for more than that.
Last edited by scandelous81; Jun 19, 2008 at 09:36 PM.
Thread Starter
Registered User
Joined: Feb 2008
Posts: 163
From: Mount Dora, Florida, US
Re: No muffler
Ya, make sure to composite blade on a chop saw for best results, after u cut it shorter and drill new holes to rivet the end cap back on take some epoxy on a brush to the areas that have been cut and drilled so the fibers dont come apart there. make sure u cut the length u want off from can from the exhaust tip side, thats the side that is free to come lose inside the can. drill the rivets out first and take the end cap off. leave the packing in and take the chop saw and cut. put the end cap back on and mark ur holes to drill, then just rivet it back together. Only cut a couple inches off there's no need for more than that.
Registered User
Joined: Apr 2006
Posts: 518
From: Philadelphia, PA, US
Re: No muffler
i wouldnt do it. I was running no muffler for a year. I loved it sounded great until the cops that you **** off everyday start following u and pull you over and right bs tickets for u. Now i made a shorty can and havnt had trouble since.
Registered User
Joined: Jan 2008
Posts: 422
From: Fort Lauderdale, Stuntshine State
WWW.IDOLRIDERS.COM
Joined: Mar 2006
Posts: 1,148
From: Sacramento, Ca, USA, Earth
Re: No muffler
Registered User
Joined: Mar 2006
Posts: 507
From: denver
