I use a 900rr master now, and I have to use two fingers to feel comfortable...My question is if I use a 1000rr master or a brembo after market master will it allow me to use only one finger and still have enough braking power? How many fingers do you all us on the handbrake?

 

i use 2 and my handbrake still don't work worth a ****.

 

1 on HB and 1 on clutch

for scrapes /circles etc...

 

i use one

 

i got a brembro i need 2 fingers on it jus incase i give a lil too much of a blip 03 1000 has alot of power lol

 

What master all you all using.......What master would you suggest to allow me to use only one finger..

 

I also use two fingers, if I use one, I don't feel safe... But i'm planning on beginning with circels, should I use the "1 on the brake, 1 on the clutch" method ?? Or should I just try to circle, and if it stalls and the engine shuts off, to bad, and just deal with it ?

 

i use 1, 2 gives me too much braking and I didn't feel comfortable

 

cheap way is 1k master...636's work good too.

darius will tell you pvm, but that is loot

 

teach, why do the 636 masters work better than lets say gsxr or older r6's?!?!?! i thought that they were the same thing?!?! but i must say that BOTH 636 masters i used (03-04) were better than others?!?!?!?!?!

 

i have a brembo master and i use 1 finger.

 

B/c The 05-06 636 Is A Radial Master Cylinder As Is A 04-05 R1 And Cbr1000rr

 

I use 2 but I'm thinking about going back to 1 finger cause stalling out SS circles is getting old and its scary. I would say that when your learning the hb use 2 cause you will blip it to much and 1 finger wont bring it back down like 2 will.

 

i know that... im asking why the 03-04 NON-Radial 636 masters work better than non-radial gsxr and r6 masters... thought it was jsut a good bleed job on my first one... but this one (my second HB with 03 636 master) works even better!!!?!?!?!?!?!

maybe it IS just the bleed job or new rotor or whatever?!?!?

 

i dunno...vertical joe told me they worked awesome. i ran a zx7 hydraulic clutch master and it kinda sucked, although i could do everythin with it. i tried a 1000rr hyd. clutch and it blew, then i tried the 1000rr front master and it is one finger!

pm me back

1000 bucks for the motor, only the motor...if ed is interested, i might be able to drop that a buck or two...maybe

 

they prabably have different piston diameters, most MC have the diameter engraved on them.

 

i just switched from 02'gixxer master to 99'900rr and it made all the differance in the world work clutch and h/b at the same time or you will be left behind

 

i have always used a 99-02 r6 front flipped since day one.... no problems, always hooked up, and has never broke. Originally, I did not feel confortable just using one finger for hc scrapes etc, so I always used two, and even for circles...... but about 2 months ago, I started playing with one finger brake, one finger clutch, and it seems to working pretty good...... I agree with the last part of what Mikey D said as well...............

-Big Scott
www.stunters.com
www.teamstunters.com

 

i use a Zx7 clutch master upside down. bill at fullthrottle inc said it works best with his rear master that he sent me.. i like it. i can use one finger no problem. but usually for combos i feel i have a better grip using two.. go figure?

-kane

 

'02 gsxr 1000 master, dual caliper and i use 2 fingers on the brake. 1 finger is not enough stopping power cuz my muscles are shot on my left arm.