Anyone know where you can get them made. Basically i have been through hell trying to get a 929/954 lower triple for my r1 forks i have tried 2 people on the forums here and both waited over a month and never received... 1 i was refunded for.

Basically long story short need a custom tapered roller bearing 30X47X15 (like the all ***** bearings) for the upper triple on the f4ez so i can use either a r1 triple clamp or gsxr triple and make things easy on myself.

or if someone knows where i can ACTUALLY get a 929/954 triple.

 

use the complete R1 triple. The bottom triple will drop right into an F4i with no modding needed

For the upper bearing you need a special one. See the pic of the box with part # (it's a 1-piece sealed bearing). Get it, remove your upper bearing race in the frame, tap in the new bearing and you're done.

 

What year R1 triple?

 

any year. I have 04, my buddy has 01, another guy here did 06. I also did one with a GSXR front end.

 

I mis read what you said. I thought you meant the r1 would just drop right in without changing anything.

Yeah that is the exact problem i was having the f4i, R1 and GSXR lower bearings are the same.... But F4i upper was different from the R1 and GSXR

THANK YOU!

 

this should be a sticky....929 954 front ends are getting hard to find but the r1 front end is pretty easy to find

 

After doing a little research you can also use NSK part # HR32906J

Which is the same diameter bearing. But is a Tapered Roller bearing like the all ***** bearings.

 

i work for a bearing co. any bearing you could need can be found at applied.com , if someone makes it this place will have it

 

I agree with OMR sticky this thread.

Again here is another bearing that is VERY common and rather easy to find

6906-2RS

 

I have a 954 lower triple if anyone needs it....

pm me.

 

been trying to find a bearing for my r1 front for a month already. thanks to this thread i can hopfully find it now. thanks man.

 

talkin about swappin front ends on the F4i...

I know you said R1, but this part will work with any gixxer front end also?
that's the only thing needed to use it if I find a whole new R1 front end?

How much does that bearing run?

thanks...

 

Lol i get get in through tucker rocky at work (motorcycle dealership) for about 4 dollars employee cost haha.


A side not its the 6906-2RS bearing which is the EXACT same as the bearing skidmark is talking about.

 

i just baught a 1999 r1 front end for my f4i who makes 6906-2RS bearing
and is this right 30x47x9...
im a new rider and after reading this page i went out and got a full front-end

 

if theres people rolling hundreds of feet on stock f4i front ends then why throw it in the trash and get a 929/954/R1 front end? if anything whynot just beef it up with better springs and fluid? i'll admit they do pogo and are a royal pain in the *** to learn stoppies on, but i did it and i dont have a damper or any mods except handlebars and steel lines. and my right fork seal leaks and has a sock zip tied around it.

 

subscribed

 

I tried to sticky a thread like this awhile back, what front ends work with the f4i, and Binder929rr talk ****

https://www.stuntlife.com/forums/443...waps-what.html

 

Sealed bearings work the best. I put a 05 GSX-R 1000 front end on a 93 GSX-R 1100 Then we did a GSX-R front end on a 600RR Sealed wheel bearings out of a GSX-R 600 wheel

 

I got em through Kaman Bearings

 

yep, i couldnt remember the name, but there is an applied down the road from my work. They have EVERYTHING in there. U bring em your size and theyll have tons for u to choose from...