Striped Screw In Stator Cover - General Sportbike Discussion

yungstunna17 · 09-06-2006, 12:50 AM

I Striped The Screw In The Stator Cover And Don't Know Whats Next....any Suggestions?

BobbyL · 09-06-2006, 01:27 AM

just tighten the rest..it will be ok

yungstunna17 · 09-06-2006, 06:49 PM

I tightened all the rest of them and i put oil in it and and came running out on stator cover side. i would say it had about a 2mm gap inclosing of it and i put oil in it which was stupid. i put silicone on the stator cover and gasket then for got to put it on the other side of the gasket so i screwed up there also. do u think i could pull out the screw that i striped?

BobbyL · 09-06-2006, 06:56 PM

well crap
only thing you can really do is get that bolt out...retap the hole and put a fresh bolt in..thats if you didnt eff up all the threads on the block

*Tanus* · 09-06-2006, 07:03 PM

put in a helicoil

yungstunna17 · 09-06-2006, 07:33 PM

So The Helicoil Will Fit Inside The Screw That Brok Off In To The Motor? And Then Just Screw It Out From There?

*Tanus* · 09-06-2006, 07:40 PM

nevermind the helicoil, you'll need to drill a small hole in the bolt then use an ez-out

yungstunna17 · 09-06-2006, 07:48 PM

Thats the feed back im getting is the same thing so that must mean i need to do that

BobbyL · 09-06-2006, 07:58 PM

oooo..you didnt strip it..you broke it off...yea you gotta get a tiny drill bit....and make sure you drill as best you can in the center of the bolt...then buy a tiny ease out and be real easy on it trying to break it loose..once its looks its cake

yungstunna17 · 09-06-2006, 08:00 PM

I'll Just Get Somebody Who Works At A Bike Shop To Do It B/c I Don't Wanna **** Up Again...and All The Screws Where Supposed To Be Diff Hah?

yungstunna17 · 09-07-2006, 12:02 AM

just tighten the rest..it will be ok

U WERE RIGHT ITS NOTHING SERIOUS I CAN JUST TIGHTIN THE REST OF THEM B/C SOMEONE JUST TOLD ME THAT SINCE ITS NOT THE BOTTOM SCREW ITS OK

09-06-2006, 12:50 AM	#1
yungstunna17 Registered User Join Date: Jul 2006 Location: Marrero,Louisiana,United States Age: Bike: 05 gsxr 600, rancher 350 Gender: Male Posts: 17	Striped Screw In Stator Cover I Striped The Screw In The Stator Cover And Don't Know Whats Next....any Suggestions?

09-06-2006, 01:27 AM	#2
BobbyL Registered User Join Date: Sep 2005 Location: Dallas..texxxxus Age: 23 Bike: 04 gsxr 600, 125cc pitbike Gender: Male Posts: 636	Re: Striped Screw In Stator Cover just tighten the rest..it will be ok

09-06-2006, 06:49 PM	#3
yungstunna17 Registered User Join Date: Jul 2006 Location: Marrero,Louisiana,United States Age: Bike: 05 gsxr 600, rancher 350 Gender: Male Posts: 17	Re: Striped Screw In Stator Cover I tightened all the rest of them and i put oil in it and and came running out on stator cover side. i would say it had about a 2mm gap inclosing of it and i put oil in it which was stupid. i put silicone on the stator cover and gasket then for got to put it on the other side of the gasket so i screwed up there also. do u think i could pull out the screw that i striped?

09-06-2006, 06:56 PM	#4
BobbyL Registered User Join Date: Sep 2005 Location: Dallas..texxxxus Age: 23 Bike: 04 gsxr 600, 125cc pitbike Gender: Male Posts: 636	Re: Striped Screw In Stator Cover well crap only thing you can really do is get that bolt out...retap the hole and put a fresh bolt in..thats if you didnt eff up all the threads on the block

09-06-2006, 07:03 PM	#5
Tanus Registered User Join Date: Jan 2005 Location: AZ streets Age: Bike: xr72,f4 Gender: Male Posts: 2,987	Re: Striped Screw In Stator Cover put in a helicoil

09-06-2006, 07:33 PM	#6
yungstunna17 Registered User Join Date: Jul 2006 Location: Marrero,Louisiana,United States Age: Bike: 05 gsxr 600, rancher 350 Gender: Male Posts: 17	Re: Striped Screw In Stator Cover So The Helicoil Will Fit Inside The Screw That Brok Off In To The Motor? And Then Just Screw It Out From There?

09-06-2006, 07:40 PM	#7
Tanus Registered User Join Date: Jan 2005 Location: AZ streets Age: Bike: xr72,f4 Gender: Male Posts: 2,987	Re: Striped Screw In Stator Cover nevermind the helicoil, you'll need to drill a small hole in the bolt then use an ez-out

09-06-2006, 07:48 PM	#8
yungstunna17 Registered User Join Date: Jul 2006 Location: Marrero,Louisiana,United States Age: Bike: 05 gsxr 600, rancher 350 Gender: Male Posts: 17	Re: Striped Screw In Stator Cover Thats the feed back im getting is the same thing so that must mean i need to do that

09-06-2006, 07:58 PM	#9
BobbyL Registered User Join Date: Sep 2005 Location: Dallas..texxxxus Age: 23 Bike: 04 gsxr 600, 125cc pitbike Gender: Male Posts: 636	Re: Striped Screw In Stator Cover oooo..you didnt strip it..you broke it off...yea you gotta get a tiny drill bit....and make sure you drill as best you can in the center of the bolt...then buy a tiny ease out and be real easy on it trying to break it loose..once its looks its cake

09-06-2006, 08:00 PM	#10
yungstunna17 Registered User Join Date: Jul 2006 Location: Marrero,Louisiana,United States Age: Bike: 05 gsxr 600, rancher 350 Gender: Male Posts: 17	Re: Striped Screw In Stator Cover I'll Just Get Somebody Who Works At A Bike Shop To Do It B/c I Don't Wanna **** Up Again...and All The Screws Where Supposed To Be Diff Hah?

09-07-2006, 12:02 AM	#11
yungstunna17 Registered User Join Date: Jul 2006 Location: Marrero,Louisiana,United States Age: Bike: 05 gsxr 600, rancher 350 Gender: Male Posts: 17	Re: Striped Screw In Stator Cover just tighten the rest..it will be ok U WERE RIGHT ITS NOTHING SERIOUS I CAN JUST TIGHTIN THE REST OF THEM B/C SOMEONE JUST TOLD ME THAT SINCE ITS NOT THE BOTTOM SCREW ITS OK