I need some advice on what you all think - General Sportbike Discussion

Swayz · 03-05-2003, 05:36 PM

I could really use some help on this if anyone recognises this please help a brother out here is the first picture , the chain came off when I was doing a wheelie a piece shot through the cover of the front sproket and did this , the problem I had is right after I stopped the bike oil and antifreeze came out and left a trail on the road and dont know what to do please help out if you can I would greatly apreciate it

Swayz · 03-05-2003, 05:39 PM

the piece were the other piece shot through was just right of the black circle (were the clutch adj. is ) the black circle is just left of the yamaha etching left of the front sproket ok I got that piece off and can see the front sproket , just to the right is were the piece snapped off and and went through the cover

Swayz · 03-05-2003, 05:42 PM

this is the front sproket , just right of that is were the piece broke off

Swayz · 03-05-2003, 05:44 PM

The leak looked like it came from the area around the two hoses , one hose goes to the radiator and the other goes somewere I dont know here is a look at the two hoses

Swayz · 03-05-2003, 05:46 PM

also the clutch does not work at all when I pull the lever but It seemed to shift if I slammed into 2ond with no clutch , this piece also came out , I found it just left of the front sproket

Swayz · 03-05-2003, 05:52 PM

so to sum it up , the clutch lever does not work at all , it leaked all the oil and antifreeze a couple hours after the chain came off , the piece just right of the sproket shot through the housing cover , a piece to the left of the front sproket the one on the board seemed to connect to the clutch lever at the end near the front sproket , and I really need to fix this can anyone help does this look familiar to any one? I apreciate it either contact me here on on aol messenger Swayz8
Swayz

MikeM · 03-07-2003, 10:34 AM

I gotta come by and look at this one day.

StreetHeat · 03-07-2003, 11:03 AM

cracked the cases, eh??.,,,,,,ummmm YEAAAH you're definitely ****ed, bro

Lb3 · 03-07-2003, 12:39 PM

I'm on my 3rd motor right now. That is gonna be a very expensive repair. You have busted a hole in your block if it is leaking oil and coolant. It's new engine time for you, or new bike time.

Swayz · 03-07-2003, 04:47 PM

I definatley need a new bike for sure but I wanna keep this one in my aresenal and modify it , I got a little further today I found out that the rubber hose is the anti freeze hose and the gold tubeing hose is the oil line the crack is right were they both meet

Swayz · 03-07-2003, 04:48 PM

another view

Swayz · 03-07-2003, 05:00 PM

does that mean the case is cracked and if so maybe it can be welded to stop the leak , also the clutch does not work and it looks like the clutch basket is fine , I have not checked the plates though but there was no slipage in the clutch when it went down? I apreciate the feedback so far thanks

Swayz · 03-09-2003, 11:49 AM

ok looks to me like I just need a new water pump , cover and maybe a new clutch cause I get no tension on the lever

SCoast AStar13 · 03-10-2003, 10:59 AM

can you clean off some of that gunk can't relly see the crack.

Raybone · 03-10-2003, 11:16 AM

a little jb weld and you should be straight

no really worse case you could have someone weld that crack?????

and as for the leakage??? some kitty litter should work

Swayz · 03-11-2003, 11:43 PM

wow that would be a treat , let me clean it up a bit and get some oil and start it up n see exactly were the leak is coming from , good look fellas

Swayz · 03-21-2003, 04:09 PM

well after all the advice and some jb weld which will dry in 15 hours, the piece in front of the front sproket I think its a bar a clutch pushrod , snapped when the chain came off , I just ordered the pushrod , there were a few other parts I did not order that goes on the right side of the bike maybe into the clutch basket I dont know , does anyone know about this I could really use some help , when I pull the clutch in which now has tension since I changed the engine sproket cover , it wont shift into gears it shifts if I powershifted though but no clutch , the basket and all the plates are ok ?? the piece in the last picture came out of the hole which is in front of the sproket and chain in this picture I apreciate all the advice

Swayz · 03-21-2003, 04:26 PM

I found this amongst the pieces

Swayz · 03-22-2003, 07:20 AM

ok the weld should be done , puttin my baby back together and starting her up today , worst case is the clutch wont shift but I can powershift it the weld will be put to the test , anyone know about the clutch pushrod , maybe I can get it workin today

Swayz · 03-22-2003, 01:22 PM

I got it started today whoaaaa , looks like the weld is working just oil shot out of the pushrod hole when I started it up hahaaa looks like thats all that needs to be fixed , waiting on the pushrod , this one I cant fix by myself I have no idea , anyone know if its an easy to replace

03-05-2003, 05:39 PM	#2
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	the piece were the other piece shot through was just right of the black circle (were the clutch adj. is ) the black circle is just left of the yamaha etching left of the front sproket ok I got that piece off and can see the front sproket , just to the right is were the piece snapped off and and went through the cover __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it " Last edited by Swayz : 03-07-2003 at 04:49 PM.

03-05-2003, 05:42 PM	#3
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	this is the front sproket , just right of that is were the piece broke off __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it " Last edited by Swayz : 03-07-2003 at 04:50 PM.

03-05-2003, 05:52 PM	#6
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	so to sum it up , the clutch lever does not work at all , it leaked all the oil and antifreeze a couple hours after the chain came off , the piece just right of the sproket shot through the housing cover , a piece to the left of the front sproket the one on the board seemed to connect to the clutch lever at the end near the front sproket , and I really need to fix this can anyone help does this look familiar to any one? I apreciate it either contact me here on on aol messenger Swayz8 Swayz __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it "

03-07-2003, 11:03 AM	#8
StreetHeat Registered User Join Date: Oct 2002 Location: Clearwater, FL Age: 27 Bike: 2004 GSXR 750, 2002 CR250R, Pocketbike Gender: Male Posts: 197	cracked the cases, eh??.,,,,,,ummmm YEAAAH you're definitely ****ed, bro __________________ "The more you sweat, the less you'll bleed."

03-07-2003, 12:39 PM	#9
Lb3 Registered User Join Date: Nov 2002 Location: Dallas, Tx Age: 28 Bike: 929 Gender: Male Posts: 4,997	I'm on my 3rd motor right now. That is gonna be a very expensive repair. You have busted a hole in your block if it is leaking oil and coolant. It's new engine time for you, or new bike time. __________________ ...

03-07-2003, 10:34 AM	#7
MikeM Free Porn - The-Nags.com Join Date: Oct 2002 Location: Driving my truck around Europe Age: 31 Bike: 09 DAF XF Gender: Male Posts: 49,777	I gotta come by and look at this one day.

03-07-2003, 04:47 PM	#10
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	I definatley need a new bike for sure but I wanna keep this one in my aresenal and modify it , I got a little further today I found out that the rubber hose is the anti freeze hose and the gold tubeing hose is the oil line the crack is right were they both meet __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it " Last edited by Swayz : 03-21-2003 at 04:25 PM.

03-07-2003, 04:48 PM	#11
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	another view __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it " Last edited by Swayz : 03-21-2003 at 04:25 PM.

03-07-2003, 05:00 PM	#12
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	does that mean the case is cracked and if so maybe it can be welded to stop the leak , also the clutch does not work and it looks like the clutch basket is fine , I have not checked the plates though but there was no slipage in the clutch when it went down? I apreciate the feedback so far thanks __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it "

03-09-2003, 11:49 AM	#13
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	ok looks to me like I just need a new water pump , cover and maybe a new clutch cause I get no tension on the lever __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it "

03-10-2003, 10:59 AM	#14
SCoast AStar13 I'm Getting Used to Posting Join Date: Oct 2002 Location: South Jersey Age: 33 Bike: TL1000R Gender: Posts: 93	can you clean off some of that gunk can't relly see the crack.

03-10-2003, 11:16 AM	#15
Raybone I Enjoy Posting At StuntLife! Join Date: Oct 2002 Location: Detroit Age: 30 Bike: 99 R6 Gender: Male Posts: 2,135	a little jb weld and you should be straight no really worse case you could have someone weld that crack????? and as for the leakage??? some kitty litter should work __________________ ""Ride It Like You Stole It"" "Live my life Raw caus' I never liked the Law" I'm doin a hundred on the freeway......so if you do the speed limit get the fock outta my way!!!!!! [URL=http://www.DetroitStreetRyders.com][img]http://www.detroitstreetryders.com/images/banners/banner.jpg[/img][/URL]

03-11-2003, 11:43 PM	#16
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	wow that would be a treat , let me clean it up a bit and get some oil and start it up n see exactly were the leak is coming from , good look fellas __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it "

03-22-2003, 07:20 AM	#19
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	ok the weld should be done , puttin my baby back together and starting her up today , worst case is the clutch wont shift but I can powershift it the weld will be put to the test , anyone know about the clutch pushrod , maybe I can get it workin today __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it "

03-22-2003, 01:22 PM	#20
Swayz Registered User Join Date: Oct 2002 Location: Brenthook NY Age: 31 Bike: yzf600 when its running Gender: Posts: 405	I got it started today whoaaaa , looks like the weld is working just oil shot out of the pushrod hole when I started it up hahaaa looks like thats all that needs to be fixed , waiting on the pushrod , this one I cant fix by myself I have no idea , anyone know if its an easy to replace __________________ AIM : Swayz8 " If your mind can conceive it then you can achieve it "